originlabdiamonds.com

Lab Diamond Wholesale Supplier Ti Hi Stacking Pattern for New Zealand

A lab diamond wholesale supplier ti hi stacking pattern is the agreed layout a New Zealand buyer and a supplier use when wholesale cartons are placed on a pallet. Ti describes how many cartons sit in one layer, and hi describes how many layers are stacked, and together they define the total cartons per pallet for that order. Even though the stones themselves are small, the outer cartons, packing list, pallet label, and receiving check all depend on this layout being agreed before packing starts. If ti, hi, carton size, and total carton count are left open, the buyer cannot easily reconcile what was ordered, what was packed, and what arrived.

How New Zealand Buyers Define the Ti Hi Stacking Pattern

For New Zealand buyers, the ti hi stacking pattern is not a supplier habit to accept after dispatch. It is a packing specification to agree in writing before cartons are sealed. The buyer should define the pattern for each order line, because a change in carton size, inner packing quantity, or order quantity can change the number of cartons in a layer and the number of layers that make a complete pallet.

Start by asking the supplier to state the outer carton dimensions, the quantity packed in each carton, and the weight of a filled carton as the supplier will pack it. Then agree the ti value, the hi value, and the resulting total cartons per pallet, and ask the supplier to show that total in the packing list format the buyer will use at receiving. Where an order does not fill a complete pallet, agree how the partial pallet will be built, marked, and counted, rather than assuming the same pattern applies.

Use the following sequence to lock the pattern down:

  1. Specify the carton and the quantity per carton for each order line.
  2. Ask the supplier to propose the ti and hi values for that exact carton.
  3. Require the supplier to confirm the total cartons per pallet that the ti and hi values produce.
  4. Specify how incomplete layers and partial pallets will be packed and identified.
  5. Ask the supplier to confirm the agreed pattern in the order confirmation and packing list.

Also agree whether the pattern may change if the order quantity changes, and require the supplier to flag any revised layer count before packing.

Lab Grown Diamond Wholesale Supply Decisions Before Packing

In lab grown diamond wholesale supply, pallet layout cannot be separated from lot and parcel control. Wholesale orders may contain several order lines that look similar once boxed, so the buyer needs a packing method that keeps each line identifiable from inner pack to outer carton to pallet. The ti hi pattern supports that control only when carton labelling and the packing list use the same identifiers.

Agree how stones will be grouped inside each carton. Specify whether different order lines, sizes, qualities, or lot references may share a carton, or whether each carton must contain a single order line. Ask the supplier to describe the inner packing, how each inner pack is labelled, and how the label on the outer carton connects to the contents list for that carton. If mixed cartons are allowed, require a carton-level contents list that the receiving team can check without opening every inner pack first.

Also agree the pallet build around the cartons. Ask what pallet type and size the supplier proposes, how cartons will be oriented in each layer, whether layers will follow the same orientation or alternate, and how the load will be wrapped or secured for the agreed journey to the buyer. The buyer does not need to accept a generic answer. Ask the supplier to describe the proposed build in words or a simple diagram, then approve that build, or request a revised build, before packing begins.

Finally, agree who checks the pallet before dispatch. Ask the supplier to confirm the carton count per layer, the number of layers, and the total carton count after packing, and to report any carton that was repacked, replaced, or moved to a different pallet. That confirmation gives the New Zealand receiving team a clear expected count to work from.

Buyer Decision Table for Pallet Layout and Carton Agreement

Use this table to turn the ti hi discussion into recorded decisions. Each row is a buyer-defined check, and the supplier response should be recorded against the order rather than left as a general assurance.

Decision areaBuyer choice to confirmSupplier response to requestAcceptance check on arrival
Cartons per layer (ti)Specify the number of cartons in each complete layer for the agreed carton sizeAsk the supplier to confirm the ti value in writing for this orderCount cartons in a complete layer and compare with the packing list
Layers per pallet (hi)Specify the number of layers allowed for the agreed carton and order quantityAsk the supplier to confirm the hi value and flag any change before packingCount layers on the pallet and compare with the dispatch confirmation
Total cartons per palletRequire the ti and hi values to produce a stated total for each full palletAsk the supplier to show the total on the packing list by palletReconcile total cartons received against total cartons listed per pallet
Carton contentsSpecify whether a carton holds one order line or may contain mixed linesRequire a carton-level contents list for any mixed cartonMatch carton identifiers to the contents list before opening inner packs
Partial palletsSpecify how incomplete layers and part-filled pallets will be built and markedAsk the supplier to identify each partial pallet separately in the documentsCheck partial pallets first and confirm the short layer count is as listed
Pallet identificationSpecify the information each pallet label must carry for receivingAsk the supplier to link each pallet label to its carton listScan or read each pallet label and match it to the correct packing list section
Load securingSpecify how the buyer expects cartons to be held as one load during handlingAsk the supplier to describe the wrapping or securing method before dispatchInspect the load for shifted, crushed, or separated cartons and record any difference
Change controlSpecify that ti, hi, carton size, or carton quantity changes need buyer approvalRequire the supplier to report proposed changes before packing, not after dispatchCompare the received build with the approved build and raise any unapproved change

Fill in the second column before sending the request for quotation. A supplier answer that leaves ti, hi, or total cartons blank is incomplete for this task.

Checking Cartons, Pallets and Documentation on Arrival in New Zealand

Receiving in New Zealand should follow the same order as the agreement. Start at pallet level, then move to carton level, then check inner packs. First, match each pallet label to the packing list, count layers, and count cartons in a complete layer. That quick check confirms whether the ti hi stacking pattern that was approved is the pattern that arrived. Record any difference before cartons are redistributed internally, while the pallet is still in its delivered build.

Next, check carton identifiers against the carton-level contents list. If a carton is damaged, opened, or appears repacked, set it aside and record its identifier, its pallet position if known, and the nature of the difference, then ask the supplier how to proceed before mixing its contents with other stock. Agree this handling rule in advance, so receiving staff do not have to improvise when a difference is found.

Then agree the documents that will accompany the shipment and the documents that will be sent in advance. Ask the supplier which documents will identify the pallets, cartons, and order lines, and specify the fields the buyer needs on each one, such as order reference, pallet identifier, carton identifier, ti value, hi value, and total cartons. Do not assume a supplier document layout will contain those fields. List them in the order, and ask the supplier to confirm the layout before the first shipment is packed.

Agree also what happens when the received count differs from the listed count. Specify who the buyer contacts, what evidence the buyer will provide, such as pallet and carton identifiers and receiving notes, and what response the buyer expects from the supplier. Writing that route down in advance keeps a count query focused on the agreed pattern and the recorded documents.

RFQ Checklist

Send this checklist with every request for quotation for palletised wholesale orders, and require the supplier to answer each point against the specific order quantity and carton proposed.

A complete response lets the buyer compare suppliers on the same packing basis. Treat a quotation that leaves pallet questions open as incomplete, and ask for the missing fields before placing the order.

Discuss Your Custom Order & Sample Specs

Review our manufacturing capabilities and core product lines, then share your specifications, target MOQ, and packaging details for a factory-direct quote.

Request Custom Sample & MOQ Quote →